pag. 7-10_WATER AERATION RESEARCHES
dx.doi.org/10.17683/ijomam/issue7.1
pag. 11-22_KNOWLEDGE MANAGEMENT APPLICATION IN VOCATIONAL TRAINING ORGANIZATIONS
dx.doi.org/10.17683/ijomam/issue7.2
pag. 23-27_STUDY ON SINTERING PROCES PARAMETERS OF BULK
dx.doi.org/10.17683/ijomam/issue7.3
pag. 28-36_RESEARCH ON FAULT FEATURE EXTRACTION OF ROLLING BEARING
dx.doi.org/10.17683/ijomam/issue7.4
pag. 37-41_EFFECT OF SN ADDITION ON MECHANICAL PROPERTIES
dx.doi.org/10.17683/ijomam/issue7.5
pag. 42-47_A NOVEL METHOD OF CONSTRUCTING OPEN 3D VIRTUAL SIMULATION
dx.doi.org/10.17683/ijomam/issue7.6
pag. 48-54_A NOVEL SELF-COLLISION DETECTION ALGORITHM FOR DUAL-ARM UPPER LIMB
dx.doi.org/10.17683/ijomam/issue7.7
pag. 55-60_RESEARCH ON OPTIMAL CONTROL METHOD OF ACTIVE NOISE
dx.doi.org/10.17683/ijomam/issue7.8
pag. 61-64_CALCULATION ELEMENTS FOR ESTABLISHING THE DESIGN OF A ROTATING MACHINE
dx.doi.org/10.17683/ijomam/issue7.9
pag. 65-69_BEHAVIOR OF COMPOSITE MATERIAL INSTRUMENTED BY OPTICAL FIBER
dx.doi.org/10.17683/ijomam/issue7.10
pag. 70-74_WIDEBAND BANDPASS FILTER DESIGN BASED ON
dx.doi.org/10.17683/ijomam/issue7.11
pag. 75-87_ENERGY EFFICIENT NETWORK MANUFACTURING SYSTEM USING CONTROLLED ELITIST
dx.doi.org/10.17683/ijomam/issue7.12
pag. 88-90_RAPID PROTOTYPING BOOST IN RESEARCH AND DEVELOPMENT
dx.doi.org/10.17683/ijomam/issue7.13
pag. 91-98_COMMUNICATION BETWEEN MULTI-AGENTS IN ROTATING MACHINERY
dx.doi.org/10.17683/ijomam/issue7.14
pag. 99-107_THE DESIGN OF INTELLIGENT CHARGER OF ELECTRIC VEHICLE
dx.doi.org/10.17683/ijomam/issue7.15
pag. 108-118_OPTIMIZATION OF THE PERFORMANCE OF MULTI-ARM SURGICAL ROBOT
dx.doi.org/10.17683/ijomam/issue7.16
pag. 119-123_ACCURATE DETECTION OF IMAGE EDGE
dx.doi.org/10.17683/ijomam/issue7.17
pag. 124-128_LOAD PREDICTION OF MICROGRID OPTIMAL OPERATION
dx.doi.org/10.17683/ijomam/issue7.18
pag. 129-137_CONTINUOUS STIRRED TANK REACTOR USING THE DUAL
dx.doi.org/10.17683/ijomam/issue7.19
pag. 138-143_STUDY ON THE RAPID PLANNING OF TRAFFIC ROUTES
dx.doi.org/10.17683/ijomam/issue7.20
pag. 144-151_A NOVEL ALGORITHM OF KINEMATICS PARAMETERS MEASUREMENT
dx.doi.org/10.17683/ijomam/issue7.21
pag. 152-157_THEORETICAL ANALYSIS OF A HYDRAULIC DRIVE SYSTEM
dx.doi.org/10.17683/ijomam/issue7.22
pag. 158-166_CONTRIBUTIONS CONCERNING THE INFLUENCE OF THE RUNNING-IN
dx.doi.org/10.17683/ijomam/issue7.23
pag. 167-171_EXPERIMENTAL STUDY ON THE TRIBOLOGICAL BEHAVIOR OF POLYMERIC MATERIALS
dx.doi.org/10.17683/ijomam/issue7.24
pag. 172-177_RESEARCH ON THE USE OF TAGUCHI’S METHOD TO MODEL THE MILLING PROCESS
dx.doi.org/10.17683/ijomam/issue7.25
pag. 178-184_TECHNICAL AND ECONOMIC STUDY ON CLEANING THE COOLING CHANNELS
dx.doi.org/10.17683/ijomam/issue7.26
pag. 185-188_EXPERIMENTAL SETUP FOR CALIBRATING FORCE TRANSDUCERS
dx.doi.org/10.17683/ijomam/issue7.27