Issue 11

pag. 3-6_CONTENTS

pag. 7-14_DYNAMIC ANALYSIS AND TESTING OF A SINGLE GIMBAL CONTROL MOMENTUM GYROSCOPE

dx.doi.org/10.17683/ijomam/issue11.1

pag. 15-22_AN INTEGRATED MODEL FOR PRECEDING VEHICLE TARGET DETECTION AND LOCATION BASED ON DEEP VISION

dx.doi.org/10.17683/ijomam/issue11.2

pag. 23-30_MOTION REALIZATION OF A SMALL DIAMETER DEEP WELL RESCUE ROBOT BASED ON ADAMS-MATLAB CO-SIMULATION

dx.doi.org/10.17683/ijomam/issue11.3

pag. 31-40_EXEPRIMENTAL TESTING OF A TREMOR COMPENSATION SYSTEM WITH BIMORPH PIEZOCERAMIC ACTUATORS USING OPTICAL METHODS

dx.doi.org/10.17683/ijomam/issue11.4

pag. 41-44_INFLUENCE OF ENVIRONMENT ATMOSPHERE ON OPTICAL FIBER STRENGTH

dx.doi.org/10.17683/ijomam/issue11.5

pag. 45-51_TECHNOLOGIES FOR EXTRACTION OF COPPER FROM COPPER SLAG BY FLOTATION

dx.doi.org/10.17683/ijomam/issue11.6

pag. 52-56_THE EFFECT OF LITHIUM CONTENT ON THE MASS OF THE PART WHEN ALLOYED WITH LITHIUM ALUMINUM

dx.doi.org/10.17683/ijomam/issue11.7

pag. 57-60_MECHATRONIC SUSPENSION SYSTEM WITH DRY AIR INFLATED NETWORK FOR LOWER LIMB PROSTHESIS

dx.doi.org/10.17683/ijomam/issue11.8

pag. 61-65_STUDY ON THE REALIZATION OF AN UNDETECTABLE MARINE DRONE AND ITS COMMAND-AND-CONTROL METHODS

dx.doi.org/10.17683/ijomam/issue11.9

pag. 66-76_AIRCRAFT FUEL TANK INSPECTION WITH HEXAPOD MOBILE ROBOT

dx.doi.org/10.17683/ijomam/issue11.10

pag. 77-83_INFLUENCE OF CYCLIC HEATING MODES ON THE WEAR RESISTANCE OF STEEL

dx.doi.org/10.17683/ijomam/issue11.11

pag. 84-88_RESEARCH ON THE DESIGN AND CONTROL OF ADVANCED EXPERIMENTAL SETUPS USED IN ACTUATORS AND PLATFORMS CHARACTERIZATION

dx.doi.org/10.17683/ijomam/issue11.12

pag. 89-94_VERIFICATION OF THE NORMAL DISTRIBUTION OF EXPERIMENTAL DATA OBTAINED BY MILLING OF ALUMINUM ALLOYS

dx.doi.org/10.17683/ijomam/issue11.13

pag. 95-97_MECHANICAL CHARACTERISTICS OF POWDERED ALUMINUM BRONZE OBTAINED FROM METALLURGICAL WASTE

dx.doi.org/10.17683/ijomam/issue11.14

pag. 98-102_HARDENING HEAT TREATMENT OF WEAR-RESISTANT CARBIDE PARTS MADE BY CASTING ACCORDING TO GASIFIED MODELS

dx.doi.org/10.17683/ijomam/issue11.15

pag. 103-106_EXPERIMENTAL METHOD FOR REDUCING OXIDE LAYER DEPOSITION ON ELECTRICAL DISCHARGE MACHINING EQUIPMENT

dx.doi.org/10.17683/ijomam/issue11.16

pag. 107-114_DEVELOPING A MODEL FOR COMPREHENSIVE AND SIMILARITY ANALYSIS OF SYSTEMS

dx.doi.org/10.17683/ijomam/issue11.17

pag. 115-118_ANALYSIS OF THE NETWORK CELL DEFORMATION USED FOR THE SUSPENSION OF LOWER LIMB PROSTHESIS

dx.doi.org/10.17683/ijomam/issue11.18

pag. 119-122_THE PROPERTIES OF HIGH-SPEED STEEL Р6М5, DEPENDING ON THE COMBINED CHEMICAL HEAT TREATMENT

dx.doi.org/10.17683/ijomam/issue11.19

pag. 123-130_METHOD OF PERFORMING THERMOPHYSICAL CALCULATION OF A PLASMA CHEMICAL REACTOR OF A NEW TYPE

dx.doi.org/10.17683/ijomam/issue11.20

pag. 131-136_EXPERIMENTAL SETUP FOR STATIC CHARACTERIZATION OF STACK-TYPE PIEZOELECTRIC ACTUATORS

dx.doi.org/10.17683/ijomam/issue11.21

pag. 137-140_THE PROBLEMS OF INDUSTRIAL 3D ABS AND PLA PRINTERS IN CERMISO CENTER

dx.doi.org/10.17683/ijomam/issue11.22

pag. 141-151_TILT ANGLE DETECTION AND CORRECTION OF LICENSE PLATE BASED ON CONVOLUTIONAL NEURAL NETWORK

dx.doi.org/10.17683/ijomam/issue11.23

pag. 152-156_ASPECTS REGARDING ECO-INNOVATION PRACTICE AND TRENDS FOR A SUSTAINABLE AUTOMOTIVE INDUSTRY

dx.doi.org/10.17683/ijomam/issue11.24

pag. 157-162_APPLICATIONS IN MEDICAL RECOVERY USING THE CRYO-SOUND MECHATRONIC SYSTEM

dx.doi.org/10.17683/ijomam/issue11.25

pag. 163-173_DESIGN OF THE MANIPULATOR SYSTEM FOR AUTOMATIC DETECTION LINE OF MECHATRONIC STRAIGHT SIDE PRESS

dx.doi.org/10.17683/ijomam/issue11.26

pag. 174-183_DESIGN OF ELECTRONIC DRIVE CONTROL SYSTEM OF THE HYDRAULIC JOINTS OF THE MANIPULATOR

dx.doi.org/10.17683/ijomam/issue11.27

pag. 184-188_STAND FOR TESTING THE SATELLITES MOTION, IN LABORATORY CONDITIONS

dx.doi.org/10.17683/ijomam/issue11.28

pag. 189-198_AUTOMATIC DESIGN OF SINGLE-STAGE SOLAR PHOTOVOLTAIC GRID-CONNECTED INVERTER SYSTEM

dx.doi.org/10.17683/ijomam/issue11.29

pag. 199-209_ONTOLOGY DESIGN AND DEVELOPMENT OF TRANSMISSION LINE IN INSPECTION ROBOT

dx.doi.org/10.17683/ijomam/issue11.30

pag. 210-215_ANALYSIS OF THE EVOLUTION AND PROSPECTS OF INTRODUCING ROBOTS AND ARTIFICIAL INTELLIGENCE IN THE ACTIVITIES OF THE MODERN COMPETITIVE SOCIETY

dx.doi.org/10.17683/ijomam/issue11.31

pag. 216-226_MODELLING OF THE FEED SYSTEM IN NUMERICAL CONTROL MACHINE TOOL USING PID CONTROL

dx.doi.org/10.17683/ijomam/issue11.32

pag. 227-234_APPLICATION OF AVR POWER AUTOMATIC SINGLE-CHIP MICROCOMPUTER TO THE ELECTROMECHANICAL MEASUREMENT AND CONTROL SYSTEM

dx.doi.org/10.17683/ijomam/issue11.33

pag. 235-242_ANALYSIS OF WAVELET NEURAL NETWORK ALGORITHM IN INVERTER FAULT DIAGNOSIS

dx.doi.org/10.17683/ijomam/issue11.34

pag. 243-248_STUDY ON IMPROVING THE MEASUREMENT ACCURACY BY TOUCH PROBE WITH A COBOTIC MULTI-APPLICATION PLATFORM

dx.doi.org/10.17683/ijomam/issue11.35

pag. 249-258_PARAMETER OPTIMIZATION OF THE FORGING AND FORMING PROCESS USING PARTICLE SWARM OPTIMIZATION

dx.doi.org/10.17683/ijomam/issue11.36

pag. 259-265_MEMS MEASUREMENT USING A PLASTIC AND METAL ARM INTEGRATED INTO A MECHATRONIC SYSTEM

dx.doi.org/10.17683/ijomam/issue11.37

pag. 266-274_SIMULATION EXPERIMENT OF HEAT TRANSFER TUBES FOR ELECTRONIC HEAT ABSORBER IN THERMAL POWER GENERATION SYSTEM OF POWER PLANTS

dx.doi.org/10.17683/ijomam/issue11.38

pag. 275-285_DISASSEMBLING PROCESS AND TECHNOLOGY OF AXIAL PISTON PUMP FOR REMANUFACTURING

dx.doi.org/10.17683/ijomam/issue11.39

pag. 286-294_MECHANICAL PROPERTIES TESTING OF CARBON FIBER REINFORCED COMPOSITES

dx.doi.org/10.17683/ijomam/issue11.40

pag. 295-302_INVESTIGATION OF THE PORTAL-TYPE MACHINE TOOL GEAR-BELT GEARBOX

dx.doi.org/10.17683/ijomam/issue11.41

pag. 303-313_SIMULATION AND OPTIMIZATION OF THE TRAJECTORY FOR HEXAPOD MINI-ROBOT HEXI

dx.doi.org/10.17683/ijomam/issue11.42